glass process machine

Glass process machine

Sand Belt Grinding Machine SDM1015

Summary
SDM1015 Glass sand belt grinding machine is easy to operate and specialize in grinding arris of flat glass. It is suitable for grinding glass edger before tempering.
Technical parameter
Power: 3.04KW
Glass size: 1m (L)*1.5m (W)
Glass thickness: 3-25mm
Sand belt (mm) (2pcs):GXK51P120
Width80*1360
Weight:150kg
Dimension (mm):900*600*1380

Flat Glass Laminating Line YJ2660

The Production Line is composed of loading and unloading table, Washing & Drying Machine, PVB roller, glass laminator, suction cup hanger, roll squeezer and heating section. The Line is especially used in manufacturing of flat safety laminated glass.

Two control systems are optional: center computer control system and Independent Section Control System, either of which is reliable in quality and the function. The whole line is PLC controlled.

★Products order can be made according to customer’s request. Our company reserves the right to renew and revise as well as cease the technology depending on design requirements.

Technical parameter:

Glass thickness	3～19mm
Laminating panel max. Thickness	60mm
Min glass size	520×550mm
Max glass size	2600×6000mm
Working height	950±20mm
Consumption of compressed air	20n m³/h (Min pressure 0.6Mpa)
Consumption of soft water	0.4 m³/h
Complementary voltage	220v
Installed power	280kw
Power consumption	230kw

Glass Washer and Drier QX26

1. Brief Introduction: QX26glass washer & drier adopt horizontal configuration, the flat glass placed on the conveyor roller, passing in-feed section, washing section, drier section, and out-feed section. Glass washing and drying machine is used for cleaning and air-drying of flat glass panes. There are various types available for different glass, float, coating and low-E glass. Washing and drying sections can be elevated or lowered as a whole with PLC. Only in this way will come off satisfactorily.

3. Features:
3.1. The high-powered washer is used primarily with manufacturing facilities for Automobile safety glass, laminated construction glass, mirror and nickel-plate glass.
3.2. Adopt washing is done with four pair of cylinder brushes. (Two pair of rough & fine brushes.)
3.3. Drying is done with high power blower dryer and is equipped with adjust air knife.
3.4.   The air resistant sections of the unit are soundproofed.
3.5.   This machines drive roll spinning transmission is achieved by utilizing chain wheel helical gear.
3.6.   The face of unit can be lift 450mm vertically, allowing easy inspection and repair.
3.7. The water tank is the unit is equipped with an electric heater to self-adjusting water temperature.
3.8. The section of the unit that comes in contact with water is made of stainless steel to prevent corrosion

★ Products can be made according to customer’s request. Our company reserves the right to renew and revise as well as cease the technology depending on design requirements.

2. Technical parameter

QX26
max. width	min width	thickness	processing speed	brushes	power	weight	dimension
2600mm	300*350mm	3-40mm	1.0m/min~6m/min	4pairs	39KW	4500kg	850045003500mm

Glass Washer and Drier QX25

1. QX25 Washer & Drier adopts horizontal structure and is used for cleaning and drying flat glass.
2. It is made up of 3 pairs of brush.
3. The washing section is adjusted by electric motor, Digital display, and the washing section can be elevated and lowered as a whole, and the Max. hoist height is 400mm.
4.Technical parameter:
Max processing size (width): 2500mm
Min processing size: 350*350mm
Processing thickness: 3~~30mm
Weight: 5500KG
Power: 23KW
Dimension: 7300*2860*3200mm

Glass Washer and Drier QX16

1. General Description
The processing speed is adjusted by variable motor with horizontal structure ,four pairs of brushers and three pairs of sponge rollers make the performance of machine reliable. The temperature of hot-air can be set in advance. Different design meets customers＇ requirements.
2.Technical Parameter
Max. size:1500*2100mm
Min. size:150*150mm
Processing thickness:3-15mm
Processing speed:0.7-3.5m/min
Brusher: 4pairs
Sponge roller: 3pairs
Power:10KW
Dimension: 4000(L)*2000(W)*1020(H)
Weight:900KG

Glass Washer and Drier QX12

1. General Description
The processing speed is adjusted by variable motor with horizontal structure ,four pairs of brushers and three pairs of sponge rollers make the performance of machine are reliable. The temperature of hot-air can be set in advance. Different designing meets customers requirements.
2.Technical Parameter
Max. size:1100*2000mm
Min. size:100*150mm
Processing thickness:3-15mm
Processing speed:0.7-3.5m/min
Brusher: 4pairs
Sponge roller: 3pairs
Power:8KW
Dimension:3400(L)*1600(W)*1020(H)
Weight:800KG

L Type Glass Straight Line Double Edge Grinding Line

1.This line including two sets of straight-line double edge grinding machine, one 90° transfer table and one set of glass Washing & Drying machine.
2.It is used for grinding the four parallel straight lines and arises of the flat glass. Rough grinding, fine grinding, polish, safe corner and washing&drying can be finished at one time.
3.It features in high precision, high efficiency, safety and stable.
4.The machine adopts PLC control system, frequency converter adjust speed, set parameter through man-machine interface.
5.The glass can be finish at one time processed, simple operation and high automatic. It is the best equipment for the mass production of glass for furniture and decoration.

Glass Straight Line Double Edge Grinding Machine SM2025

1.General description:
SM2025 Glass straight-line double edging machine is suitable for grinding two parallel straight-line edge of flat glass, rough, fine and polishing at one time, its feature of high precision, efficiency and secure .the lathe bed use the double straight-line guide rail and ball-bearings, the drive is smooth and reliable. The product adopts the PLC control, speed control by transducer. Set parameter via the intelligent interface. Finish to work at one time, the operation is easy and convenient.
SM2215/25/30/40 available in different models(from1500mm to 4000mm width), each of which is produced in 22 spindles (11spindles per side with safety corner cutting)

2.Technical Parameter

Model	Max. width	Min. width	Thickness	Speed	Voltage	Weight	Dimension
SM2025-1	1500mm	120mm	3-12mm	0.5-4.5m/min	45kw	6000KG	398031101760
SM2025-2	2500mm	300mm	3-25mm	0.5-4.5m/min	47KW	7500Kg	4860 4360 1760
SM2025-3	3000mm	300mm	3-25mm	0.5-4.5m/min	47KW	8000KG	486050601760
SM2025-4	4000mm	300mm	3-25mm	0.5-4.5m/min	47KW	8500KG	486060601760

Glass Straight Line Double Edge Grinding Machine SM8

SM8 available in processing glass with thickness 3-12mm, which is produced in 8 spindles (4 peripheral wheels per side) rough, fine grinding; polishing can be finished at a time. Adopt PLC for controlling. The SM8 are also suitable for small production batches.
Mainly Parameter:
The height of work table: 950mm
Diagonal error of processing glass: 2m×2m≤1mm
Parallel error of processing glass: ≤0.5mm/2m
Air pressure: 0.4-0.8Mpa

Glass Straight Line Double Edge Grinding Machine SM8Y

1.Brief Introduction:
SM8Y available in processing glass with thickness 3-19mm, which is produced in 8spindles (4 peripheral wheels per side) rough, fine grinding; polishing can be finished at a time. Adopt PLC for controlling. The SM8Y are also suitable for small production batches.
2. Technical Parameter
Dimension (L*W*H): 2700*2890*1650mm
Working table height: 850mm
The Min. area of processing glass: 120*120mm
Processing glass width: 120-1500mm
Processing glass thickness: 3-12mm
Processing glass Diagonal error: 2m*2m≤1mm
Processing glass parallelism error: ≤0.5mm/2m
The speed of transmission of processing glass: 0.5-4.5M/Min. (According to the thickness of glass to adjust)
Power: 21KW
Voltage: 380V/50HZ
Air pressure: 0.4-0.8MPa
Weight: 4000Kg

Glass Straight Line Pencil Edge Grinding Machine ZM7Y

1.Brief Introduction
1.1 It can process pencil/OG edging edges of different glass thickness with different shape wheels.
1.2 Rough grinding, fine grinding and polishing of the pencil edge can be finished at one time.
1.3 Same thickness of glass sheet can be process continually.
1.4 The brightness of pencil edge will be close to the original glass after polished.
1.5 this machine is easy to operate and has good performance.
2 Working condition
2.1 Power: AC380V±10% 3φ 50HZ±2%
2.2 Environment temperature: 1~40
2.3 Air relative humidity: 90%.
3.Technical Parameter & Wheels Disposal
3.1 Processing glass thickness: 3 ~ 15mm
3.2 Min. size processing glass: 120mm×120mm
3.3 Processing speed: 0.54～～5m/min
3.4 Installation power: 13.6KW
3.5 Occupation land: 6.6m (L) ×1.1m (W)
3.6 Dimension: 3.6m(L) ×0.9m(W) ×1.5m(H)

Glass Straight Line Edge Grinding Machine ZM4

The 4-spindle ZM4 suitable for processing straight-line edge & 45° arrises of glass sheet with various size and thickness. Rough grinding, fine grinding of flat edge and rough grinding of arris can be finished at one time. The same thickness of flat glass can be continuously processing.
Technical parameter:
A. Processing glass thickness: 3-25mm
B. Angle of arris: 45°
C. Min. size of glass: 120mm×120m
D. Processing speed: 1.0-5.0m/min
E. Installed power :9.15KW;
G. Dimension : 3300x900x1500mm
Working condition:
Power: AC380V±10% 3phase 50HZ±2%
Environments temperature: 1~40°C

Glass Straight Line Edge Grinding Machine ZM8

1. Brief Introduction:
1.1 The ZM8 is suitable for processing straight-line edge & 45° arrises of glass sheet with various size and thickness.
1.2 The main base is made of cast iron.
1.3 Production speeds is adjusted by step-less motor.
1.4 Input and output conveyor adopt timing belt which can improve the transmission precision.
1.5 It is easy to operate and has good performance.

2. Operation Condition
2.1 Power supply: AC380V±10% 3phase 50HZ±2%
2.2 Environment Temperature : 1~40°C
2.3 R.H:90%
3. Technical Data& Wheel Layout
A. Processing glass thickness: 3-28mm
B. Angle of arris: 45°
C. Min. size of glass: 120mm×120m
D. Processing speed: 1.0-5.0m/min
E. Installed power (ZM8): 16.3kw ;
F. Occupation of land: (ZM8): 6.6m×1.1m
G. Dimension (ZM8): 3.9m×0.9m×1.5m

Glass Straight Line Edge Grinding Machine ZM9

1. General Description
1.1 ZM9 is suitable for processing straight-line edge & 45°arrises of glass sheet with various size and thickness.
1.2 The main base is made of cast iron.
1.3 Glass thicknesses is adjusted by a servomotor and showed on a digital display.
1.4 A special design of the in-feed section for controlling the desired amount of glass removal without adjusting each spindle individually.
1.5 Independent felt wheel and the cerium water recirculation system make the flat edge more shining.
1.6 Input and output conveyor adopt timing belt which can improve the transmission precision.
1.7 It is easy to operate and has good performance.
2. Model Explanation
ZM9 9spindles totally: 5spindles for the straight-line edge (adopt the independent wool felt wheel), 2pieces of spindle for front and back arris each.

3 Operation Condition
3.1 Power supply: AC380V±10% 3phase 50HZ±2%
3.2 Environment :Temperature : 1~40
3.3 R.H: 90%
4. Technical Data
A. Processing glass thickness: 3-28mm
B. Angle of arris: 45°
C. Min. size of glass: 120mm×120m
D. Processing speed: 1.0-5.0m/min
E. Installed power :18.5KW;
F. Occupation of land: 6.9m×1.1m
G. Dimension : 3.9M×0.9M×1.5m

Glass Shape Edging Machine YXM1

YXM1 Glass Shape Edging Machine is suitable for processing the edge of round shape, oval shape & other irregular shape of glass sheet with various size and thickness. It can be process the round & oval shape glass semi-automatically.

Adopts the different wheels to processing different shape like semicircular, flat edge and OG edge etc. Adopt the cup shape wheel and adjust the angle of motor can be processing the bevel edge.

Technical parameter

1. degree of vacuum should be reached: -0.08MPa~-0.1MPa

2. water pressure: 0.1MPa~0.2MPa

3. Air source pressure: 0.6MPA~0.8MPa

4. Rotating speed of working table: 0.3rpm~3rpm

5. Rotating speed of independent turn plate: 0.7rpm~7rpm

6. Min. incurvature radius: R100mm

7. Max. rotating radius: 1.5m

8. Height of working table: 1.1m

Glass Internal and External Shape Edging Machine YM1

YM1 inter & external shape edging machine applies to grind and polish for shaping peripheral edge of circular, ellipse and irregular flat glass, and also applies to semi-automatic grinding for circular and elliptical glass. Using different shaping grinding wheels can obtain the half- round, flat or OG edges of glass.

Main technology specification:

Environment temperature: 1℃　～ 40℃

Relative air humidity: ≤ 90﹪

Applied vacuum degree scope: -0.05 MPa～-0.1 MPa

Water pressure: 0.1 MPa～0.2 MPa

Air supply pressure: 0.6 MPa～０.8 MPa 68L/min

Glass thickness: 3 mm～40 mm

Glass external diameter: φ100 mm～φ1600 mm

Glass internal diameter: φ150 mm～φ600 mm

Maximum radii of curvature: R75mm

Rotation speed of spindle: 2850r/min

Rotation speed of working table: 0.4 r/min～2.0 r/min

Installation power: 4.2KW

Total height of the main machine: 1915 mm

Max rotating radii: 960 mm

Height of working table: 1100mm

Weight: About 700Kg

Glass Straight Line Beveling Machine XM251A

XM251A suitable for processing bevel & bottom edge of glass sheet with various size and thickness. The function of digital display processing thickness, angle and remaining thickness. Brightness of edge as clear as the glass itself after polished. Operation Condition 1 Power supply :AC380V±10% 3phase 50HZ±2%； 2 Environment Temperature : 1℃~40℃； 3 R.H:＜90%
Technical Data Processing speed: 0.73~3.65m/min Min. glass size: 120×120mm Glass Thickness: 3~20mm Remain thickness: ≥1.5 Bevel width: max 30mm Bevel angle: 3°~30° Size of machine: 7780×1250×2550mm Size of main part: 4366×1225×1560mm Base dimension: 2832×667 Height of guide track: 842mm Length of guide track: 2345mm Net Weight: 4050kg Power: 16.83KW

Glass Straight Line Beveling Machine XM351

1. Brief Introduction:
1.1 This machine is designed for grinding and polishing a bevel edge, with bottom round edger of glass with different size and thickness.
1.2 Rough grinding, fine grinding, polishing of bevel and grinding of bottom edge can be completed in one time.
1.3 Processing thickness, angle and remaining thickness appears on digital display.
1.4 The processing speed is adjustable with a step-less motor which offers a wide range of speed selection.
1.5 Input and output conveyor adopt timing belt which can improve the transmission precision.
1.6 The grinding wheels are indirectly connected to the motor by a belt to reduce vibration.
1.7 This machine features high efficiency and precision, stable quality, easy operation and low wear.

2. Technical Parameter
Processing speed: 0.73~.365m/min
Min. glass size: 120*120mm
Glass Thickness: 3~20mm
Remain thickness: ≥1.5mm
Bevel width: 30~60mm
Bevel angle: 0~30˚
Size of machine: 8270×1250×2520mm
Weight: 5000KG
Power: 22.83KW

Glass Straight Line Beveling Machine XM354

1. XM354 is used for grinding bevel and flat bottom edger of glass in different size and thickness.
2. Rough grinding ,fine grinding, polishing of bevel and grinding of bottom side can be completed in one time.
3. It is easy for feeding of grinding spindle in the all and beveling angle while the thickness of glass is being changed.
4. The brightness of finished surface will be almost the same as glass itself.
5.Technical Parameter:
Min. processing size: 80*80mm
Processing thickness: 3~~~20mm
Processing speed: 0.73~~~3.65m/min
Max. width of bevel: 30mm
Bevel degree: 30~~~300
Weight: 5500KG
Power: 25.21KW
Dimension: 8900*1250*2520mm

Glass Vertical Drilling Machine LZ25

LZ25 glass vertical drilling machine is controlled by computer. In actual operation,

just put the glass on the transmission belt, input drilling position data, press the

start button, the machine will automatically position itself and finish all drilling

operations, and automatically stop when the work is completed. Featuring high

drilling efficiency and accurate position, suitable for the processing of building

glass and furniture glass.

Main technical parameters:

Drilling diameter	B=φ4~φ60mm	Size	7000×2020×3620mm
Glass thickness	δ=5~30mm	Drill connector	Taper K=60℃; Bolt hole G1/2"
Max. height of glass	2500mm	Weight	3000Kg
Min. Size of glass	500×150mm	Power	6.45Kw
Speed of X axis	1~5m/min	Power supply	380V 3φ 50Hz
Speed of Z axis	1~5m/min	Air pressure	0.6~0.8Mpa
Drilling tolerance	±0.5	Relative humidity	≤90%

Glass Horizontal Drilling Machine ZJ130

1.General description:
1.1) ZJ130 Glass drilling machine is a cold processing machine which is easy to drill holes on sheets of glass and is equipped with upper and lower drilling bit.
1.2) An automatic cylinder drives the lower-drill bit while the upper bit is operated by manual.
1.3) Holes of different sizes can be achieved with bits of different diameters.
1.4) this machine works efficiently, it has low glass damage and is easy to operate.
Technical Parameters
1.  Hole Diameter: φ5φ220
2.  Glass thickness range: 3 ~20 mm
3.  Max. size of Processing glass: 2700×2200mm
4.  Height of Working Table: 1000mm
5. Distance between drilling center and back column:1300mm
6. Hole at drilling axis and drilling bit connection end: taper k=60°, screw hole G1/2
7. Size: 750×2200×1700mm(L×W×H);      2200×2500×1700mm (with floating working table)
8. Weight: 1200KG (with floating working table)
9. Voltage: 380V/50Hz
10. Power: 4.95Kw(with air compressor 1.5kw)